THOMSON SPEEDTOUCH 536V6 DRIVER DOWNLOAD

It just increases the errors and reduces the ping. Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community. Do isolation test and see if you get different results. Yeah, I only had Windows firewall on and turned it off which didn’t change anything. These will now be the known defaults on startup:. Guessing its the same as a speedtouch v6, here you go..

Uploader: Gardabei
Date Added: 21 September 2017
File Size: 30.50 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 71385
Price: Free* [*Free Regsitration Required]

The default was Administrator with a blank password, and according to Primacall’s setup info, this thmoson was optional, and you could just click Next to skip it.

Setting up a Speedtouch 536v6 DSL modem

The cd will do the same thing. But again, I can’t say for certain until the next drop out. To re-set the Speedtouch to factory defaults you need to disconnect from power, press the reset button with a pen or pinkeep it pressed, reconnect power and continue to keep the button pressed 536vv6 at least 15 seconds until the power and ethernet lights flash alternately red and green. If you haven’t complained then the sync is slow for some other reason than Thoomson deliberately slowing you down.

Posted 17 May You certainly shouldn’t be having drop out issues with that much margin. Sign in Already have an account?

Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community. Sign up for a new account in our community.

Recent Drivers  DRIVERS FOR SONY VGN-CR510E

Archive View Return to standard view. You never need the cd for these boxes, and it causes more issues than it solves. Are they in the good range or too high or low? Go wpeedtouch setup page on the modem and run the setup wizard. Share this post Link to post Share on other sites.

Technicolor / Thomson SpeedTouch 536

These will now be the known defaults on startup:. The connection will drop out only briefly and when it comes back the modem sync is always lower. If it is wrong you might need to statically set it.

Is that the same thing you’re talking about? I did an isolation test last night with the OPEN modem and it kept dropping out. What results from isolation test?

Alcatel / Thomson / Technicolor SpeedTouch v6

Is there any way around this so I can finish the configuration, or am I going to have to call Primacall support? Guessing its the same as a speedtouch v6, here you go. Try making sure software firewall isn’t blocking access to modem’s interface if not the case it.

The attenuation and SN margin is what I want to know about mostly.

SG :: Technicolor / Thomson SpeedTouch DSL Modem

I’ve also tried resetting the unit with the reset button on the back, but no joy there unless I’m getting the sequence wrong – or it’s disabled by firmware like the ones issued by Telstra in Australia.

Recent Drivers  MESSAGER 2 R560 DRIVER

Just went through the process again and now it’s back to normal. Yeah, I only had Windows firewall on and turned it off which didn’t change anything.

Posted xpeedtouch May Try factory resetting the Speedtouch again from the button on the back hold it in for 30 sec then release and then turn off the modem allow it to rest for a couple of minutes and switch it back on and try your luck then Could something have gone amiss there? It was all pretty straightfoward until the last screen in the setup wizard, which asks you to set a username and password for the modem, not the one for the DSL connection.

Turning off interleaving speedtojch not actually alter the sync speed. So I thought I’d start fresh and factory reset it, which I’m sure I’ve done before with this modem with no problems.

The reason I’m concerned is I’m having a few issues with BigPond and I know that if i go through tech support they’re going to want me to use their provided modem thinking that will fix the issue.

I was playing around with the same model too — managed to set it up in bridge mode