Power Management for USB 2. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Please refer to below illustrations for the pin definition of onboard headers. Do not force to insert the CPU into the socket if above situation is found. A p p l y thermal interface material onto c e n t e r of IHS on the socket surface. This motherboard supports Dual Channel Memory Technology.

Uploader: Tugami
Date Added: 17 February 2013
File Size: 56.55 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 96681
Price: Free* [*Free Regsitration Required]

Please select “Front Mic” as default record device. Locate Pin1 and the two orientation key notches. This motherboard supports Untied Overclocking Technology.

Before you of “User Manual” in the support CD. Power Management for USB 2.

No part of this installation guide may be reproduced, transcribed, 945cm-s, or translated in any language, in any form or by any 945gcm- except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

If no jumper cap is placed on pins, the jumper is “Open”. The Support CD that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. Otherwise, it will operate at single channel mode. If you use AC’97 audio panel, please install it to the front panel audio header as below: It delivers excellent performance with robust design conforming to A S R o c k ‘ s c o m m 945cgm-s t m e n t to quality and endurance.


In other words, it is able to provide exceptional power saving and improve power efficiency without sacrificing computing performance.

Products and 945gcms names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins. S e c u r e load lever with load p l a t e tab under retention tab of load lever.

It’s a community-based project which helps to repair anything. Therefore, the drivers y o u install can w o r k properly. This motherboard supports Dual Channel Memory Technology.

Please refer to below steps for the software setting of Multi-Streaming. Specifications 954gcm-s information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. Verify that the C P U is within the socket and properly mated to t h e orient keys.

When the jumper cap is placed on pins, the jumper is “Short”.

ASRock GCM-S, LGA Socket, Intel Motherboard | eBay

This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. Otherwise, the CPU will be seriously damaged. Fasten the card to the chassis with screws. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.


ASRock 945GCM-S, LGA775 Socket, Intel Motherboard

The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. When you discard the Lithium qsus in California, USA, please follow the related regulations in advance. Then, the drivers c o m p a t i b l e to your system can be auto-detected and listed on the support C D driver page. Rotate the load plate to fully open position at approximately degrees.

To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system.

Please refer to the instruction of your IDE device vendor for the details. Do NOT place jumper caps over these headers and connectors.

Doing so m a y d a m a g e the motherboard. Please follow the order from up to bottom side to install those required drivers. It should be done at your own risk and expense.